How Ya Are? Audio Crew Service Manuals X-treme ESSB Audio Forum Where all your Hi-Fi Audio Questions are Answered |
 |
WZ5Q's Studio "X" The Pro Audio "Racks"  "My Chilrens"  |
| How Ya Are? Audio Crew Service Manuals X-treme ESSB Audio Forum Where all your Hi-Fi Audio Questions are Answered |
|
WZ5Q's Studio "X" The Pro Audio "Racks" "My Chilrens" |
These are the Set-up and Settings Developed by the Voodoo Master Himself.... W5UDX.
SETUP:
1) You will have a Balanced Cable coming into the Input of Channel 1 using the typical TRS 1/4" connector or XLR connector utilizing the 3ea wires (Signal +, Signal -, and Shield)
2) The Output of Channel 1 going into the Input of Channel 2 will be using an Unbalanced Cable with the Mono 1/4" connector utilizing 2ea wires (Signal +, and Shield).
(You can use TRS 1/4" connectors for this if you short the Signal - and the Shield together on both ends of the cable. Doing this makes it an Unbalanced Connector)
3) You will have a Balanced Cable going out of the Output of Channel 2 using the typical TRS 1/4" connector or XLR connector utilizing the 3ea wires (Signal +, Signal -, and Shield)
Just another note:
If you were using Unbalanced Cables coming into the Input of Channel 1 and going out of the Output of Channel 2, then you would use the opposite Balanced Cable to tie Channels 1 and 2 together.
SETTINGS:
Try these settings to start out with, as we do not know your Audio line up. Also the best place that we found to put the EX3200, is in between the EQ and the Compressor.
Channel 1:
SHIFT |
= Set to Ultra Low (Light on) |
BASS PROCESSOR |
= Set to "1" |
MODE |
= Set to Soft (light off) |
AUTO NR |
= Set to IN (Light on) |
NR SENSITIVITY |
= Set to where the LED Display just barely goes to full scale on voice peaks |
TUNE |
= Set to 3.3 |
PROCESS |
= Set to Exciter |
HIGH MIX |
= Set to "1" (be careful with this as it will introduce "Tearing" into the audio if set to high) |
SOLO |
= Set to Off (Light is out) |
IN |
= Set to IN (Light is on) |
SURROUND |
= Set to IN (Light is on) |
SURROUND |
= Control set to "1-2" |
Channel 2:
SHIFT |
= Set to Ultra Low (Light on) |
BASS PROCESSOR |
= Set to "2" |
MODE |
= Set to Soft (light off) |
AUTO NR |
= Set to IN (Light on) |
NR SENSITIVITY |
= Set to where the LED Display just barely goes to full scale on voice peaks |
TUNE |
= Set to 5 |
PROCESS |
= Set to Enhancer |
HIGH MIX |
= Set to "1" (be careful with this as it will introduce "Tearing" into the audio if set to high) |
SOLO |
= Set to Off (Light is out) |
IN |
= Set to IN (Light is on) |
You will hear a phenomenal increase in Sub Harmonic Low end and Brilliant Clarity in the rest of the Frequency Response.
You might have to reduce the boost on the low end with the EQ and use the Bass Processor Controls on the EX3200 to increase the Harmonic content of the Low End.
The last thing to adjust will be the Compressor, which will smooth out the whole effect.
One Word of Warning.......
You have to have some Low End in your Voice and have a Mic able to pick up that Low End to give the Sub Harmonic Processor something to work with. Most everyone that has badmouthed the EX3200 has had a High Squeaky Voice!! Hi Hi!
Enjoy Hammy Radio!!
From Deep Down in the Dark Dismal Swamps of the Calcaseau...
Asta La Tacos!
WZ5Q
"Behringer EX-3200 Set-up" page designed by PAP
