help please connection ts 950sdx with sm-230 scope 8 pin din

Force them Rigs to accept True Voodoo!
Post Reply
g0uut
Voodoo Audio Head
Posts: 12
Joined: Fri Jul 16, 2010 3:18 am

help please connection ts 950sdx with sm-230 scope 8 pin din

Post by g0uut » Thu Apr 28, 2011 4:35 am

i need some help
is any one use the ts 950sdx +sm230 ????i need info of the 8 pin din in the 950sdx
i have the kenwood ts 950sdx +sm-230 scope
i need to know how to connect it with the din pin pluge

i have the info of the pin on the sm-230 monitor
but not on the ts 950sdx

sm230------------------------------------------------------ts950sdx
1--GND-----------------------------------------------------?
2--MARKER ON/OFF---------------------------------?
3SCAN WIDTH INORMATION----------------------?
4--N.C--------------------------------------------------------?
5--SCAN WIDTH INFORMATION-------------------?
6---N.C----------------------------------------------------------?
7--MARKER POSITION VOLTAGE----------------?
8--GND-----------------------------------------------------------?
WHAT PIN FROM THE SM-230 GOING to what pin in the ts 950sdx
may be you can ask kenwood when ever you have time
many thanks
elan
g0uut

User avatar
Voodoo Guru
VooDoo Site Admin
Posts: 718
Joined: Wed Feb 23, 2005 8:47 am
Location: Down there on the right...

Post by Voodoo Guru » Fri Apr 29, 2011 1:38 am

Howdy Elan,
This information can be found in the SDX Service Manual.

Look on Page 255 Zone A2 for the CN12 connector that attaches to the J3 8-Pin DIN Plug for the Scope, this is on the Carrier Unit.



Image



Now turn to Page 214 which lists the Terminal Functions of the connectors. Look under the Carrier Unit heading for CN12. This will list the Terminal numbers and their Terminal Function.



Image


Now you must interpolate which pins on the J3 connector go to the CN12 Connector.
This is what we came up with....

SM230-------------------------------------- TS-950SDX
1--GND------------------------------------- 1 -- Analog GND
2--MARKER ON/OFF----------------------- 2 -- Sub Marker Control
3SCAN WIDTH INORMATION------------ 3 -- Span Switch Info
4--N.C------------------------------------- 4 -- N/C
5--SCAN WIDTH INFORMATION--------- 5 -- Span Switch Info
6---N.C------------------------------------ 6 -- N/C
7--MARKER POSITION VOLTAGE-------- 7 -- Sub Marker Signal
8--GND------------------------------------ 8 -- Digital GND

So Basically it is a direct Pin for Pin connection.
All you should need is a 8-Pin Jumper cable.


Good Luck!
Voodoo Guru
From Deep in the IDD of the Sub-Harmonix Realm

py1fr
Audio Head
Posts: 1
Joined: Mon Feb 04, 2019 1:42 pm

Re: help please connection ts 950sdx with sm-230 scope 8 pin din

Post by py1fr » Tue Feb 05, 2019 7:01 pm

Hi guys!
I need this Din 8 pin conector. It is completely different . I did not find anyone here in BrasiL that fix in scope terminal in my TS-950SDX and SM-230. I found only 8 pin Din 270 and 262 grades.
Any help?
73!

User avatar
Voodoo Guru
VooDoo Site Admin
Posts: 718
Joined: Wed Feb 23, 2005 8:47 am
Location: Down there on the right...

Re: help please connection ts 950sdx with sm-230 scope 8 pin din

Post by Voodoo Guru » Wed Feb 06, 2019 2:41 am

py1fr wrote:
Tue Feb 05, 2019 7:01 pm
Hi guys!
I need this Din 8 pin conector. It is completely different . I did not find anyone here in BrasiL that fix in scope terminal in my TS-950SDX and SM-230. I found only 8 pin Din 270 and 262 grades.
Any help?
73!
We no longer have an SM230 or the cables to look at or compare, but looking at the 8 Pin Scope Jack on the back of the SDX, it looks like the horseshoe type which is the 262.

IIRC, there are only two versions of 8 Pin DIN, the 270 and 262.

They are cheap enough on ebay to get one and try?

Good Luck!
Voodoo Guru
From Deep in the IDD of the Sub-Harmonix Realm

Post Reply