I've thought to add the FX2000 with preset # 62 ULTRBASS but have to figure out where exactly... Like last piece (after the DSP2024), before the DSP2024, or between DEQ2496 and EX3200... ???
I'd also appreciate some nice settings for the preset #62.
My current setup:
Behringer T-1 microphone
MIC2200
DEQ2496 (with PEQ, DEQ and DYN on)
EX3200
MDX2600
DSP2024 (sometimes on PLAT, sometimes on STUD)
73,
Nico
Behringer VIRTUALIZER 3D FX2000
Behringer VIRTUALIZER 3D FX2000
Last edited by IT9PQJ on Sat Jan 11, 2014 5:59 pm, edited 1 time in total.
Hi you all!
Hope this will be useful to someone.
Work is in progress, but I've done the following up until now...
My usual setup:
Behringer T-1 microphone
MIC2200
DEQ2496 (with PEQ, DEQ and DYN on) --> I'd like to find out more on this DYN staff, so any suggestion is welcome, although I believe I'll find out on my own soon!
EX3200
MDX2600
DSP2024
...At the moment the FX2000 is between the compressor MDX2600 and the other effect processor DSP2024 (this one uses PLAT or STUD effects found on this forum). It already does its job but I want to try put it in a couple of other combinations in order to see any difference in audio processing.
I've modified its preset #62 U.BAS original settings... I'll try to post them later if required.
73,
Nico
Hope this will be useful to someone.
Work is in progress, but I've done the following up until now...
My usual setup:
Behringer T-1 microphone
MIC2200
DEQ2496 (with PEQ, DEQ and DYN on) --> I'd like to find out more on this DYN staff, so any suggestion is welcome, although I believe I'll find out on my own soon!
EX3200
MDX2600
DSP2024
...At the moment the FX2000 is between the compressor MDX2600 and the other effect processor DSP2024 (this one uses PLAT or STUD effects found on this forum). It already does its job but I want to try put it in a couple of other combinations in order to see any difference in audio processing.
I've modified its preset #62 U.BAS original settings... I'll try to post them later if required.
73,
Nico
- Voodoo Guru
- VooDoo Site Admin
- Posts: 719
- Joined: Wed Feb 23, 2005 8:47 am
- Location: Down there on the right...
Hi Guru!
Thanks for your interest!
Combination is as the following and that's the only one I've tried so far since as it seems to be working fine:
MIC2200
DEQ2496
EX3200
MDX2600
FX2000
DSP2024
I wish we could meet on the air someday. I'm active most of the time on 10m (from around 28.350 to 28.500... 28.730 is too high for me since as my ANT is almost a dummy load up there... Looking forward to modify it so that I can use the whole 10m range).
Best regards,
Nico
Thanks for your interest!
Combination is as the following and that's the only one I've tried so far since as it seems to be working fine:
MIC2200
DEQ2496
EX3200
MDX2600
FX2000
DSP2024
I wish we could meet on the air someday. I'm active most of the time on 10m (from around 28.350 to 28.500... 28.730 is too high for me since as my ANT is almost a dummy load up there... Looking forward to modify it so that I can use the whole 10m range).
Best regards,
Nico